Duravent DuraPlus HTC Manuale Utente

DuraPlus htcInstallation Instructions

section, with the bead resting on the circular opening in the plate (Fig 8). Slide the Collar down on top of the Radiation Shield to complete the Fi

at least a minimum of 10 inches (250 mm) high, but must also extend above the level of the insulation. The Firestop Radiation Shield has a

not interfere with the Roof Flashing. Secure Roof Radiation Shield to the roof using at (2) roong nails or (2) #8, 1-1/2” wood screws as shown in

   ELBOW DEGREECHIMNEY LENGTHOFFSET INCHES RISE INCHES OFFSET INCHES RISE INCHES OFFSET INCHE

the elbows is limited to no more than 50% of the overall chimney pipe of the system (e.g. if the total chimney pipe run is 20-ft, then no more than

EXTENDED ROOF BRACKET INSTALLATION If the chimney extends more than 4 feet (1.2 m) above the rooine, an Extended Roof Bracket must be installed eve

CHIMNEY SECTIONCATHEDRAL CEILING INSTALLATIONADJUSTABLE FLASHINGCAPSTORM COLLARBOTTOM OF SUPPORT BOX NEEDS A MINIMUM OF 3 INCHES ( 75mm) CL

sealant. Attach the bottom end of the Adjustable Legs to the Roof Brackets using the nuts & bolts provided.ROOF SUPPORTED INSTALLATION

Note: You may not have an oset below the Roof Support with DuraPlus HTC Chimney (you may still have an oset with the connector pipe).1. Cut and

TALL CONE FLASHINGVENTILATED CHASE ENCLOSURETEE SUPPORT BRACKET (SHOWN INSTALLED ABOVE THE TEE)ACCESS DOOR FOR CLEANINGTEESUPPORTED INSTAL

A MAJOR CAUSE OF CHIMNEY RELATED FIRES IS FAILURE TO MAINTAIN REQUIRED CLEARANCES (AIR SPACES) TO COMBUSTIBLE MATERIALS. IT IS OF THE UTMOST IMPORTAN

CHIMNEY SECTION AS BRANCH FOR TEEBACK OUTSIDE PORTION OF WALL THIMBLEWALL THIMBLE EXTENSIONS IF NEEDEDFRONT INSIDE PORTION OF WALL TH

ADJUSTABLE WALL STRAPBACK OUTSIDE PORTION OF WALL THIMBLE ATTACH TO WALL WITH SCREWS PROVIDEDTEE SUPPORT BRACKETCHIMNEY TEETEE S

back portion of the Wall Thimble to the outside wall using (4) 8-penny nails or (4) #8, 1-1/2” wood screws in the holes provided (Fig 24). Seal the

lock Tee Cap into bottom of either the Tee or Chimney Cleanout section.6. Install Branch onto Tee: From inside the home, attach a section of chimne

than 4 feet (1.2 m) above the top Wall Strap or Flashing, use an Extended Roof Support Bracket.9. Flashing: It is recommended that a Tee Supported

1/2½" 12mm AIR GAP ESTABLISHED BY SPACERS6" 150mm MINIMUM CLEARANCE BETWEEN BOTTOM OF CAP AND CHASE TOP FLASHINGCHIM

CHIMNEY MAINTENANCE 1. Creosote and Soot: When wood is burned slowly, it produces tar and other organic vapors, which combine with expelled moistu



DuraPlus HTC is a registered trademark of the M&G DuraVent, Inc.All rights reserved. Made in the USA. M&G DuraVent is a member of M&G Gro

CONTENTSClearances, Permits, Applications, Equipment & Materials . .. . .. . . . . . . . . 4Installation Notes, Chimney Height . . . . . . .

CLEARANCESAlways maintain at least a 2-inch (50 mm) clearance between DuraPlus HTC Chimney Pipe and any combustible materials. Never ll any require

INSTALLATION NOTES Proper planning for your DuraPlus HTC Chimney installation will result in greater safety, eciency, and convenience, as well as s

inches (38 mm) from each Chimney Section’s height to calculate installed height.CHIMNEY ENCLOSURE REQUIREMENTS Through Rooms: Interior chimneys shal

Review the step-by-step directions before beginning your installation. CEILING SUPPORTED 1. Place Appliance: Position the appliance according to th

members using the (6) 1-1/4” long, round head wood screws provided (see Fig 6). 4. Frame Openings: Cut and frame additional openings in each ceiling

2INCH 50mm CLEARANCE TO INSIDE OF ENCLOSUREFRAMED ENCLOSUREMINIMUM OF 3INCHES 75mm BELOW FINISHING CEILING18INCHES 450mm MINIMUM CLE