Duravent DuraStack Installation Manuale Utente

PIDIS REV. 2 04/2013Listed to standards:UL 103 and ULC S604UL-1978 (DIS only)ULC/ORD-C959 540°C and 760°CReport # 3162834 WARNINGSFAILURE TO

TEE CAP (TC)1. Use to block one of the openings of horizontal or vertical tee.2. Removable, it facilitates access for inspection and maintenance

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.11Figure 18 - Offsets MHS (refer to table 7)Figure 19 - Minimum offsetMHSOffset *Ø 3° 15° 30° 45°5

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.12SECTION C - STRUCTURAL SUPPORT AND GUIDINGANCHOR PLATE ASSEMBLY (AP)1. The anchor plate suppor

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.13Figure 23 - Method #1 installation StepsSealant beadSealant beadMethod #1 - Step 1 and 2Method #

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.14WALL GUIDE (WG)1. The wall guide is used as a lateral guide to resist lateral or side load only

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.15SUSPENSION BAND (SB)1. Suspension band is used to support and guide the chimney in h

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.16ROOF BRACE (RB)1. The roof brace is used to stabilize the chimney where it extends more than 15

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.17SECTION D - ROOF AND WALL PENETRATIONSROOF/FLOOR PENETRATION 1. The roof/floor penetration consi

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.18SECTION E - TERMINATIONS, STARTING ADAPTORS, DRAIN LENGTH AND RELIEF VALVE STARTING ADAPTOR

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.19Figure 43 - Flanged adaptor (FHA illustrated)Flanged adaptorHalf ringBeam clampAppliance flanged

TABLE OF CONTENTSIntroduction ... page 2Testing / listing information ...

Figure 49 - Drain lengthDrain tubing(by others)DrainDrain lengthTrap height equal to max appliance outlet pressureFigure 50 - Relief Valve installatio

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.21 BELLOWS EXPANSION JOINT (LB)1. Used in diesel or turbine exhaust installation for expa

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.22Figure 51 - Bellow Joint installation on Diesel EngineFlip top (FT)Anchor plate ventilated (APV)

23X min. = EXPANSION + 3 [inch]EXPANSION = (length[feet]/100)x(∆T[°F]/100)Operating Temp. [°F] Max distance with one Adjustable length [feet]200 20030

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.24VARIABLE LENGTH1. The variable length (LV) is used only to make odd lengths, it doesn’t compen

UP TO 6 INCH W.C. INTERNAL PRESSUREAdjustable length (LA)Adjustable length (LA)Adjustable length (LA)NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCA

26SECTION G - GREASE DUCT APPLICATION (DIS ONLY)ACCESSGrease Duct installations require provisions for cleaning the interior of the duct. NFPA 96 cle

Standard tee with dam POSITION #2(T90D2)NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.27GREASE TEE 90° (GT90P) / TEE 90 DAM (T90D) (DIS ONLY)The

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.28NO TOOL ACCESS DOOR - REMOVAL FOR INSPECTION OR CLEANING1. Unscrew the six (6) wing screws wit

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.29Figure 77 - Fan adaptor FAN ADAPTOR PLATE (FAN) (DIS ONLY)1. The fan adaptor is designed to co

APPLICATIONUL 103 Building Heating Appliance Chimney Listing:Under this category, models DIS and DAS have been determined suitable for venting flue gas

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.30SECTION H - MARKINGSSAFETY LISTING LABELS - DIS AND DAS

31NOTES

32WARRANTYThese products have a limited warranty. Please read the warranty to be familiar with its coverage.Retain this manual. File it with your othe

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.4 WARNINGSDO NOT INSTALL ANY TYPE OF INSULATION IN THE REQUIRED CLEARANCE SPACES SURROUND

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.5CHIMNEY AND FITTING JOINT ASSEMBLYAll components have a male and female end. The installation or

* MVS = Maximum Vertical Spacing between two guides or a support and a guide in a vertical position.** H = Maximum freestanding Height above t

CHIMNEY WEIGHTChimney weight is given in pounds per foot of chimney for each diameter. It is important to know the weight of the chimney section for

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.8TERMINATION HEIGHTChimneys and vents shall terminate above the roof level in accordance with the

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.9SECTION B - TEES, ELBOWS, INCREASERS90° TEE (T90)1. Generally used to connect the horizontal le